No results were found for the filter!
Rotary ventilator ASPIROMATIC stainless steel Rotating stainless steel vent that can also be used as a gas vent for all opening types, protected against backdrafts and supports the correct draft of the chimney. The (folding) extraction fan runs on ball bearings and is propelled by...
from €298.00
Art.-Nr.: 1836...
REFLEKS-adapter for ASPIROMATIC ventilator Fits the REFLEKS 90 mm flue pipe system, in order to attach the small ASPIROMATIC ventilator (Art-Nr. 1836-160). Stainless steel, 1 mm wall thickness. Diameter 95 / 150 mm, height 95 mm.
€107.00
Art.-Nr.: 1836...
DICKINSON exhaust hood Exhaust hood for DICKINSON stove pipes. H - shaped, for difficult ventilation situations. Stainless steel. As a Dickinson importer and wholesaler, we carry just about every original spare part and accessory.
from €227.00
Art.-Nr.: 4116...
Flue pipes REFLEKS This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets. Made of acid-proof stainless steel (wall depth 0.6 mm). Plugs together: slightly conical with pressed sleeve on one side.
from €29.90
Art.-Nr.: 4250...
Flue pipe elbow 45° REFLEKS This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets. Made of acid-proof stainless steel (wall depth 0.6 mm). Plugs together: slightly conical with pressed sleeve on one side.
from €56.90
Art.-Nr.: 4251...
Flue pipe elbow 90° REFLEKS This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets. Made of acid-proof stainless steel (wall depth 0.6 mm). Plugs together: slightly conical with pressed sleeve on one side.
from €61.00
Art.-Nr.: 4251...
Flue pipe elbow 90° REFLEKS with cleanout door This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets. Made of acid-proof stainless steel (wall depth 0.6 mm). Plugs together: slightly conical with pressed sleeve on one side.
from €69.90
Art.-Nr.: 4251...
Flue gas damper REFLEKS Pipe socket with draft flap for draw regulation and performance improvement of REFLEKS stoves. The exhaust ventilation is installed directly over the stove and when used automatically guides air into the exhaust guide pipe. Recommended...
from €133.00
Art.-Nr.: 4252...
Flue guard REFLEKS Guard for flue pipes that are installed in close quaters. Avaiable in stainless steel, brass or copper plate. The risk of contact burns is minimized, but the warmth of the pipe can still be enjoyed. Matches REFLEKS flue pipes of 70 mm or...
from €109.00
Art.-Nr.: 4254...
Wall shade inox Small reflector plate for heat protection behind flue pipes. Plate stainless steel. Measurements: 50cm high, 15cm wide. Available as flat or recessed version. The flat plate must be mounted with spacers or insulation behind, the recessed...
from €35.90
Art.-Nr.: 4255...
Wall mount for REFLEKS oil heaters 66 M/M-C This wall mount from stainless steel was developed by REFLEKS specifically for their oil heaters 66 M/M-C. Simply mount the heater with screws to a bulkhead instead of on the floor.
€69.80
Art.-Nr.: 4263...
Spare burner pot REFLEKS It is possible, that a replacement becomes necessary after years of usage, since the burner chambers in all REFLEKS oil heater are made from steel plate. The chambers are shipped complete with welded infeed tube, with a stainless steel...
from €217.00
Art.-Nr.: 4264...
Top seller
